As we know that the polycarbonate lenses mounted on the LED headlights of most modern vehicles are very light and withstand cracking and chipping better than normal glass. However, over years of exposure to the outside, these lenses can turn out to be yellow and hazy, lowering visibility at night, let alone they don’t look very eye-catching. You can rebuild your lenses to a near factory-fresh appearance and save money over replacements, by polishing and wet-sanding the surface of the lense. Now, let’s take a look at the step by step guide.
1. You should mask off the place around your headlight lense with painter’s tape. And then clean the whole lens with water and a mild soap to clean any dust and debris. And then you should try the lens with a lint-free cloth.
2. Put a piece of 1,000 grit sand paper in cold water about several minutes. Start sanding across the lens horizontally.
3. Change the sand paper with the next finer grit count, and vertically sand the whole surface of the lens. Be sure to remain the lens and paper wet during the process. And now you should repeat this step with each finer grit sand paper, replacing the direction of your sanding motion each time.
4. Again, wash the lens with water. Dry the lens and apply an car polishing compound. Polish the lens with a clean cloth to remove any remaining elements.
Audi’s newly newly re-designed Audi A3 is going to be revealed at this week’s Geneva Motor Show, but Audi has released images and details before the car’s official unveiling.
Keeping in line with current styling trends, the new A3 sports minimized projector headlights, larger front vents and a more aggressively styled front end. The car looks to have more pronounced character lines across the door, giving the restyled A3 a sense of speed and motion, even while standing still.
Inside, Audi’s MMI controller interface has been redesigned to be smaller. The system will concentrate on the touchwheel, which combines the touch-pad features of the A6 and A6 with the scroll wheel currently used on the A3. The new system will enable users to write characters with finger motions.
If there’s bad news for driving enthusiasts, it’s this: Audi has replaced the A3’s traditional handbrake with an electromagnetic parking brake. In other words, you’ll need to perfect your “Scandinavian flick” technique instead of relying on the parking brake to initiate tail-out cornering.
Two rocker switches will be used to control operation of the telephone, navigation, media and radio settings. Softkeys located next to the touchwheel can be used to scroll through available menus, which are depicted using the industry’s first 3D graphics.
On the subject of driving there are a few major causes of decreased visibility: dark of night, fog and rain. Given that life does not come to an end if it is dark or there’s bad weather, we still ought to get locations irrespective of whether visibility is perfect for driving or not. The good thing is that there are some measures that you can take to be sure that when your visibility is the ideal that it may be when you have someplace to be.
The setup is often plug and play, you hook up the wiring harness to your present headlight wiring system and then discover a safe position to attach the ballast and ignitor and then put up the light bulbs because you would the standard halogen items that you are exchanging. Not too much work for the end outcome, which in turn is much clearer nights time driving.
You can also look to fog lights for safer driving when it is the weather that is marking it tougher to see while driving a vehicle. Most cars do at least have fog lights as an alternative so putting in an aftermarket unit of HID fog lights can simply be done, often with a package that suits in the factory stock fog light spot. Even much better, for cars that have a fog light choice the wiring is normally in place from the plant so all that you have to do is mount the lights and get the proper switch from your car or truck dealer’s parts counter. It does not get much easier than that.
Regardless of whether your vehicle was not on the market with a fog light choice you still have choices to increase fog lights to your car, it is just a lttle bit more work. You will need to buy a common fog light kit. With a universal kit there is somewhat more planning and work included since you will need to identify a power source and support a toggle switch someplace to turn on the lights when it is necessary.
Generally this will imply splicing into a wire with a 12 volt power source and course-plotting a wire into the passenger inner compartment of the car where the move will be positioned. You will probably need to drill holes to install this switch, so pick the spot sensibly. You will also have to drill holes to attach the lights themselves. For this choose a place where the holes that you drill can very easily be hidden, but enable the lights to project in front of the vehicle.
If you take these steps to upgrade your car lights then you will no longer dread driving when visibility is lessened, you will actually look forward to it. For more information about HID headlights or HID fog lights come check out our website: carpart4u.
Today, we are going to discuss what takes place when your auto battery dies. How to choose a new battery and how to discover what the problem is. Well now let’s have a look at it.
The first and most apparent symptom that your vehicle needs a new battery is the moment you put the key in the ignition switch it, and nothing changes. In some cases, you will hear a small click that is typically the starter cylinoid engaging, but perhaps the battery doesn’t get enough power to turn the engine over. Then you can turn the projector headlights on and see if there is enough power for the lights.
Let’s do some testing to see if we can find it out. To start with, open the hood and take a peek around for dirty connections, corrosion, terminals and then you should use a tester to find how much voltage is. If the battery is below 11 volts, it possibly ought to be changed.
Then we are going to look under the hood and attempt to find where the battery is. The two primary identifying features of the battery will probably be the two big cables and the two big lead terminals leaving them. That enables the battery voltage and cranking amps to head to the starter. Next, find out the top post battery. You can notice these are named posts; they are lead to conduct just as much electricity as possible. They are coming straight up out of the top, top post. These posts are a little bit different sizes, therefore if you change the cables you must be careful to obtain the right size for negative and positive.
That is so that you don’t cross the cables. To take away a side post bolt you may need a 6 mm metric box end wrench or pliers. Now you can carry out a basic test on this battery just before removing it from the auto or purchase a new one.
If you are looking to cleaning your headlights so that they look great and admirable, it is advised that you look at following through the guide below. In incorporating what is shown on this guide, you will come to the overall realization of a great method that will help you to come to learn of how to clean your lights.
Through using the methods that are outlined, you will remove scruff marks and smudges that soap and water has been unable to remove. The main principle that cleaning up your lights incorporate is the use of scratching on the headlights to remove any dirt that is there then buffing up the headlight with higher grade rubbing compound that has finer particles to ensure that you come to the excellent realization of a great method that you can use.
You should start cleaning your LED headlight by using a coarse sand paper of 600grit. This removes most of the dirt that might be there through scratching. You should not be worried if your headlight looks a little hazy as this is the result of the scratching of the sand paper. You should next use the finer sand paper of about 1500 grit to smoothen out the coarse lines that might have been made by the coarse sand paper. It should be noted that a lot of force need not be used as this makes the process difficult in the later stages. The force of your hand is enough and this should be done in single horizontal strokes starting from the bottom going up.
Next, use turtle wax rubbing compound to ensure that you even out the scratches that were made by the sand paper. This needs hard pressure to achieve the desired effects of clear headlight. To finish up this process, buff up the headlight using a sponge with Plastic X. this will ensure that you get a stunning headlight that you will be glad to show off.